MANDRILLIS Better Gear. Better Sound.
How to Fix Double Triggering on Electronic Drums (8 Fixes)

Guides

How to Fix Double Triggering on Electronic Drums (8 Fixes)

Double triggering happens when one hit on a pad plays two sounds, or when hitting one pad also sets off another. It makes fills sound messy and recordings hard to edit. This guide explains why it happens and walks through eight fixes, from module settings like mask time and crosstalk to head tension and pad placement.

Quick Answer

To fix double triggering on electronic drums, raise the pad's mask time or retrigger cancel setting in the module, lower sensitivity slightly and raise the threshold. If hitting one pad triggers another, raise the crosstalk cancel setting and move pads so they do not touch. Tighten loose mesh heads and check that the pad type setting matches the pad.

D Daniel Brooks • Editor, Audio and Music Gear • Last updated: Nov 22, 2026 • 6 min read

How this guide was put together

This guide is based on manufacturer manuals, published specifications and widely used audio reference standards. Mandrillis does not run hands-on tests for these guides, so treat figures as typical values and check the manual for your own gear before changing settings.

What Double Triggering Looks Like

Double triggering means one hit plays more than once. You might hear a flam on a single snare hit, or a tom that sounds twice.

A related problem is crosstalk, where hitting one pad also triggers a different pad nearby. Both are common and usually fixed in the module.

  • One hit sounds like two.
  • Hitting a tom also triggers the snare or a cymbal.
  • Loud hits trigger extra notes.
  • Problems get worse at high volume or with hard hits.

Trigger Settings and What They Do

Common module settings for fixing double triggers. Names vary by brand.

Setting What it controls Change to fix double hits
Mask time or retrigger cancel Ignores extra signals right after a hit Raise it a little
Threshold Minimum hit strength that triggers Raise it slightly
Sensitivity How strongly the pad responds Lower it slightly
Crosstalk cancel Blocks triggers from nearby pads Raise it for the affected pad
Pad type Matches settings to the pad model Select the correct pad

Fix 1: Check the Pad Type Setting

Modules use the pad type setting to choose default trigger values. If the wrong pad is selected, double triggers are common.

Open the trigger settings and confirm each input matches the pad connected to it. This is especially important after adding or swapping pads.

Fix 2: Raise Mask Time

Mask time, sometimes called retrigger cancel or scan time, tells the module to ignore extra signals for a short moment after a hit.

Raise it in small steps and test with single hits. Too high a setting can make fast rolls drop notes, so stop as soon as the double hits disappear.

How to Test

Use the same test each time so you can compare.

  • Play single hits at medium and loud levels.
  • Play a fast single stroke roll.
  • Listen for doubled notes or dropped notes.
  • Adjust one step at a time.

Fix 3: Adjust Threshold and Sensitivity

If the pad triggers on tiny vibrations, raise the threshold slightly. If loud hits produce extra notes, lower the sensitivity a little.

Balance these so soft ghost notes still register. Check the module's hit level meter while you play.

Fix 4: Raise Crosstalk Cancel

Crosstalk happens when vibration from one pad travels through the rack into another. The other pad's sensor picks it up as a hit.

Raise the crosstalk cancel setting on the pad that is falsely triggering, not the one you hit. Raise it gradually, since too much can block real soft hits.

Fix 5: Move Pads Apart

Pads that touch each other or share a clamp pass vibration easily. Make sure pads and cymbals have a little space between them.

Check that cymbals do not swing into other pads or the rack when hit.

  • Leave a gap between every pad.
  • Tighten clamps so pads do not wobble.
  • Check cymbals swing freely.
  • Mount cymbals on separate arms where possible.

Fix 6: Tension Mesh Heads

Loose mesh heads can flap and trigger twice. Tighten the head evenly with a drum key, turning each lug a little in a star pattern.

Aim for a firm, even feel. Very loose or uneven heads cause unreliable triggering.

Fix 7: Check the Cables

Damaged or loose cables can create false signals. Reseat each cable firmly in the pad and module.

Swap a cable with a known good one to rule it out. Keep cables tied neatly so they do not get pulled during playing.

Fix 8: Check the Kick and Hi Hat

Kick pads often double trigger when the beater bounces off the pad. Adjust pedal spring tension and avoid burying or bouncing the beater.

On the hi hat, make sure it is calibrated, since a poorly set controller can create extra sounds.

Reset and Update if Needed

If settings get confusing, a factory reset returns trigger values to default. Back up custom kits first.

Check the maker's site for module updates, which sometimes improve triggering.

When to Contact the Maker

If one pad still double triggers after every fix, its sensor may be faulty. Try connecting it to another input to see if the problem follows the pad.

Contact the maker while under warranty. Do not open pads or the module yourself.

Use the Hit Level Meter

Most modules show a meter or number for each hit. Watching it while you play is the fastest way to see what is going on.

If one hit shows two readings, it is a double trigger. If hitting a tom shows a reading on the snare input, it is crosstalk.

What to Look For

Play slowly and watch the meter after each hit.

  • Two readings from one hit: raise mask time.
  • Readings with no hit: raise threshold.
  • Readings on another pad: raise crosstalk cancel.
  • Loud hits maxing out: lower sensitivity.

Rack and Floor Vibration

A wobbly rack passes more vibration between pads. Tighten every clamp and make sure the rack legs sit level and firmly on the floor.

Playing on a hard floor can also bounce vibration back into the rack. A drum rug under the whole kit helps, and it reduces noise too.

  • Tighten all rack clamps.
  • Level the rack legs.
  • Use a drum rug.
  • Keep the kick tower separate from the rack if possible.

Playing Technique Matters Too

Very hard hits create more vibration, which makes crosstalk and double triggers more likely. Hitting near the center of mesh pads usually triggers most evenly.

Let the stick bounce off the head rather than pressing into it. A relaxed stroke triggers cleanly and is easier on your hands and the pads.

Save Your Settings

Once you find good trigger settings, write them down or save them if your module allows it. Settings can be lost after a reset or update.

Keeping a note of each pad's mask time, threshold and crosstalk values saves time if you need to set them again.

The Bottom Line

Check the pad type, raise mask time and adjust threshold and sensitivity first. For crosstalk, raise crosstalk cancel and move pads apart.

Tighten mesh heads, check cables and pedal bounce, and reset or contact the maker if a pad keeps misbehaving.

Electronic Drum Kits From Our Reviews

Popular electronic drum kits with adjustable trigger settings.

Roland TD-07KV2

Roland TD-07KV2

Mentioned

Who Should Buy It

  • First-time buyers who want a kit they will not outgrow in a year
  • Home players who stream songs over Bluetooth and record over USB
  • Students who want a metronome and coach function on the module
  • Drummers who want two crashes and a dedicated ride from the start

Skip It If

  • You need the head material confirmed as mesh in writing
  • You want a pedal, throne and headphones included
  • You are on a budget tier and only need a four-pad starter
Check Price on Amazon

We may earn a commission at no extra cost to you.

Last verified: October 2026

Roland TD-07DMK2

Roland TD-07DMK2

Mentioned

Who Should Buy It

  • First-time drummers who want a kit from an established module line
  • Apartment players who stream songs over Bluetooth and practice on headphones
  • Students who will use a metronome and coach mode daily
  • Home recordists who want USB audio and MIDI without an interface

Skip It If

  • You need two crashes and a ride in the box
  • You want written confirmation of mesh heads
  • You are shopping in the budget tier for a four-pad starter
Check Price on Amazon

We may earn a commission at no extra cost to you.

Last verified: October 2026

Donner DED-300X

Donner DED-300X

Mentioned

Who Should Buy It

  • Adults who want a full-size layout rather than a compact starter
  • Players who use rim and edge sounds on the toms
  • Headphone practicers who want quiet mesh heads
  • Home players who will record MIDI over USB

Skip It If

  • You need a built-in speaker for casual play
  • You want the kick and hi-hat mechanisms confirmed in writing
  • You prefer a module from a reference brand with deeper editing
Check Price on Amazon

We may earn a commission at no extra cost to you.

Last verified: October 2026

Keep Reading

Related guides and picks on Mandrillis:

FAQs

Mask time may be too low or sensitivity too high. Raise mask time slightly and lower sensitivity.
It is when hitting one pad triggers another through rack vibration. Raise crosstalk cancel on the pad that falsely triggers.
Yes, loose heads can flap and trigger twice. Tighten them evenly with a drum key.

About This Guide

D

Daniel Brooks

Daniel Brooks edits the buying guides and how-to articles at Mandrillis. He works from manufacturer manuals, published specifications and common owner questions to explain music and audio gear in plain language, from turntables and headphones to digital pianos and electronic drums.

Read our full research methodology.