MANDRILLIS Better Gear. Better Sound.
Why Does My Record Player Skip on New Records? (8 Fixes)

Guides

Why Does My Record Player Skip on New Records? (8 Fixes)

A new record that skips is frustrating, and the record is not always to blame. This guide shows how to find out whether the problem is the turntable or the vinyl, then walks through eight fixes from the simplest setting to a true pressing defect.

Quick Answer

A record player usually skips on new records because the tracking force is too light, the anti-skate is set wrong, or the turntable is not level. New vinyl can also carry dust, static or leftover release agent from the factory. Check the turntable setup first, then clean the record before you assume it is defective.

M Mandrillis Team • Expert guides. Real advice. • Last updated: Nov 21, 2026 • 5 min read

How this guide was put together

This guide is based on manufacturer manuals, published specifications and widely used audio reference standards. Mandrillis does not run hands-on tests for these guides, so treat figures as typical values and check the manual for your own gear before changing settings.

First, Find Out: Is It the Record or the Turntable?

Before you change anything, run two quick tests. They tell you where to focus and save a lot of guessing.

Play an older record you know plays cleanly. If it skips too, the turntable setup is the problem. If only the new record skips, the vinyl or its surface is the likely cause.

  • Skips on every record: look at tracking force, anti-skate, leveling and the stylus.
  • Skips only on one new record: look at dust, static, warps and pressing defects.
  • Skips at the same spot every time: likely a defect or debris in that groove.
  • Skips at random spots: usually vibration, a light tonearm or static.

8 Reasons a Record Player Skips on New Records

Work through these in order. The first four are setup fixes that cost nothing. The last four deal with the record itself.

1. Tracking Force Is Too Light

Tracking force is how hard the stylus presses into the groove. Too little, and the stylus bounces out during loud or bass-heavy passages. New records are often cut louder, so they expose a light setting fast.

Check the recommended range for your cartridge. Many common cartridges sit between 1.5 and 2.5 grams. Set the counterweight to the middle of that range and listen again.

  • Balance the tonearm so it floats level before you set the force dial.
  • A small digital stylus scale makes this far more accurate.
  • Never go above the maximum listed for your cartridge.

2. Anti-Skate Is Set Wrong

While a record plays, the tonearm is pulled slightly toward the center. Anti-skate pushes back to keep the stylus centered in the groove.

Too little anti-skate makes the arm jump inward. Too much makes it skip outward. A good starting point is to set the anti-skate dial to the same number as your tracking force.

3. The Turntable Is Not Level

A tilted platter makes the tonearm drift to one side of the groove. Place a small bubble level on the platter and check it front to back and side to side.

Adjust the turntable's feet or add thin shims under the furniture until the bubble sits centered. Even a slight tilt can cause skips on loud tracks.

4. Vibration From Floors or Speakers

Footsteps on a bouncy floor and bass from nearby speakers can shake the stylus out of the groove. This is common with light turntables on hollow furniture.

Move the turntable onto a solid surface away from the speakers. A wall shelf is the best fix for a floor that flexes when you walk.

5. Dust and Static on Fresh Vinyl

New records pick up dust from the paper sleeve and build static as you slide them out. That static pulls dust into the grooves and can even tug on the stylus.

Brush the record with a carbon fiber brush before each play. If dust keeps coming back, give the record a gentle wet clean and switch to an anti-static inner sleeve.

6. Leftover Release Agent From the Factory

Pressing plants use a release agent to help records come out of the mold. Traces can stay in the grooves and make the first few plays sound rough or skip.

A careful wet clean with distilled water and a drop of mild soap usually removes it. Rinse with plain distilled water and let the record dry fully before you play it.

7. A Warped or Dished Record

Records can warp in shipping or when stored near heat. Lay the record on the platter and watch the edge as it spins. If it rises and falls, the record is warped.

A mild warp often plays fine once tracking force is set correctly. A heavy warp can throw the stylus out of the groove, and a record clamp or weight may help hold it flat.

8. A True Pressing Defect

Sometimes the record really is faulty. A bubble, a bump or a non-fill in the vinyl can make the stylus jump at the same spot every time.

Look at that spot under a bright light at an angle. If you see a raised bump or a dull, grainy patch, the pressing is defective, and the seller or label should replace it.

Check Your Stylus Too

A worn or dirty stylus cannot track the groove well. Fluff wrapped around the tip lifts it out of the groove like a tiny ski.

Look at the tip with a flashlight. Clean it gently with a stylus brush, moving from back to front only. Most styli last somewhere around 500 to 1,000 hours of play, so replace it if it is old or looks bent.

If you just installed a new cartridge, check that it sits straight in the headshell. A cartridge twisted even a little to one side pulls the stylus against one groove wall, which can cause skips and uneven wear. Many turntables include a paper alignment guide for this step.

Skip Causes and Fixes

Start at the top and work down.

Cause How to spot it Fix
Light tracking force Skips on loud parts Set force mid-range
Wrong anti-skate Jumps in or out Match to tracking force
Not level Arm drifts one way Level the platter
Dust or static Random skips, crackle Brush and wet clean
Warped record Edge rises and falls Use a record weight
Pressing defect Same spot every time Return the record

A Quick Order of Fixes

When a new record skips, run through this short list before you return it. Most skips stop by step three.

  • Brush the record and the stylus.
  • Set tracking force to the middle of the cartridge's range.
  • Match anti-skate to the tracking force.
  • Level the turntable and move it away from speakers.
  • Wet clean the record if it still sounds rough.
  • Inspect the skip spot for a bump or warp before you return it.

Turntables With Adjustable Tracking and Anti-Skate

A tonearm you can set properly is the best defense against skipping. These models from our reviews offer it.

Pro-Ject Debut PRO B

Pro-Ject Debut PRO B

Mentioned

Who Should Buy It

  • Pro-Ject fans who want a deck with a balanced design path and do not mind adding their own cartridge
  • Listeners who prioritize a stable plinth and aluminum platter over convenience features
  • Buyers who prefer manual speed control without automation
  • Users building a component system around a turntable with separate phono stage

Skip It If

  • You need an all-in-one turntable with built-in phono preamp and Bluetooth
  • You want a complete cartridge included and clearly listed in the product data
  • You require precise dimensions and weight before purchasing
Check Price on Amazon

We may earn a commission at no extra cost to you.

Last verified: October 2026

Audio-Technica AT-LP60XBT

Audio-Technica AT-LP60XBT

Mentioned

Who Should Buy It

  • Beginners who want a plug-and-play vinyl setup
  • Desktop users needing compact powered monitors with balanced inputs
  • Listeners who value automatic tonearm operation and Bluetooth streaming
  • Those building a small room system with future upgrade potential

Skip It If

  • You require a remote control for volume and track selection
  • You have limited space without checking exact dimensions first
  • You already own a receiver and passive speakers that would be underused
Check Price on Amazon

We may earn a commission at no extra cost to you.

Last verified: October 2026

Technics SL-1210M5G

Technics SL-1210M5G

Mentioned

Who Should Buy It

  • Turntablists who need instant, stable torque for scratching and beat juggling
  • Vinyl collectors who DJ and want a trusted direct-drive mechanism
  • Club and bar installs that want a proven, familiar deck at the booth
  • DJs who value precise, repeatable one-button pitch switching

Skip It If

  • You have no mixer or phono preamp and do not plan to buy one
  • You only play digital files and never touch a physical record
  • You need confirmed weight and power figures before purchasing
Check Price on Amazon

We may earn a commission at no extra cost to you.

Last verified: November 2026

Keep Reading

Related guides and picks on Mandrillis:

FAQs

It is not normal, but it is common, and the turntable setup is often the cause. Check tracking force and anti-skate before you blame the record.
A coin adds weight, but it is uncontrolled and can wear your records and stylus faster. Set the tracking force properly with the counterweight instead.
Return it if it skips at the same spot on a correctly set up turntable and you can see a bump or flaw. Clean it and check your setup first, since most skips come from those.

About This Guide

M

Mandrillis Team

The Mandrillis editorial team researches and compares audio and music gear using manufacturer documentation, verified specs and real buyer feedback, so you can make a confident purchase without wading through marketing claims.

Read our full research methodology.