MANDRILLIS Better Gear. Better Sound.
Does Anti-Skate Really Matter on a Turntable? (Plain Answer)

Guides

Does Anti-Skate Really Matter on a Turntable? (Plain Answer)

The anti-skate dial is one of the most confusing parts of a turntable. This guide explains the pulling force it corrects, what happens when it is set too low or too high, how to set it in a few minutes, and when you can safely leave it alone.

Quick Answer

Yes, anti-skate matters. While a record plays, a small force pulls the tonearm toward the center, so the stylus presses harder on one groove wall. Anti-skate pushes back to keep it centered. Without it you can get uneven wear, distortion in one channel and skips. Start by setting it to match your tracking force.

M Mandrillis Team • Expert guides. Real advice. • Last updated: Nov 21, 2026 • 6 min read

How this guide was put together

This guide is based on manufacturer manuals, published specifications and widely used audio reference standards. Mandrillis does not run hands-on tests for these guides, so treat figures as typical values and check the manual for your own gear before changing settings.

What Skating Force Is

A pivoting tonearm is offset at an angle so the stylus lines up with the groove. Because of that angle, friction from the spinning record pulls the arm toward the center of the platter.

That pull is called skating force. It is small, but the stylus tip is tiny, so even a small force changes how it sits in the groove. The tip presses harder on the inner groove wall and lighter on the outer one.

  • The inner groove wall carries the left channel on a stereo record.
  • The outer groove wall carries the right channel.
  • Uneven pressure means one channel can sound different from the other.

What Anti-Skate Does

Anti-skate applies a gentle outward push on the tonearm to balance the inward pull. When the two forces match, the stylus sits evenly between both groove walls.

Turntables do this in different ways. Some use a small spring dial, some use a hanging weight on a thread, and some use magnets. The goal is the same in every case.

What Happens If Anti-Skate Is Wrong

Both too little and too much cause problems. The signs are often subtle at first, so it helps to know what to listen for.

Too Little Anti-Skate

The stylus leans on the inner groove wall. Over time, that wall and that side of the stylus wear faster.

You may hear distortion or a harsh sound in the right channel on loud passages, since the outer wall is not being read firmly. The arm can also jump toward the center on dynamic tracks.

  • Fuzzy or distorted right channel on loud parts.
  • Uneven stylus wear over time.
  • Skips that jump toward the center of the record.

Too Much Anti-Skate

The stylus is pushed against the outer groove wall instead. That wears the outer wall and the other side of the tip.

Distortion moves to the left channel. On some decks, the tonearm can drift outward or skip back toward the edge of the record.

  • Fuzzy or distorted left channel on loud parts.
  • The arm slides outward when you lower it.
  • Skips that jump back toward the outside.

How to Set Anti-Skate in Three Steps

You do not need special tools. Set tracking force first, because anti-skate is matched to it.

Step 1: Set the Tracking Force

Balance the tonearm so it floats level, zero the counterweight dial, then set the force to the middle of your cartridge's recommended range.

For most common moving magnet cartridges, that is about 1.5 to 2.5 grams. Many people use 2 grams as a starting point.

Step 2: Match the Anti-Skate Dial

Turn the anti-skate dial to the same number as your tracking force. If the force is 2 grams, set anti-skate to 2.

This is the starting point most makers recommend. It works well for most setups.

Step 3: Fine Tune by Ear

Play a record with loud vocals or busy passages near the end of a side, where distortion shows first. Listen to each channel.

If the right channel sounds harsh, raise anti-skate a little. If the left channel sounds harsh, lower it a little. Move in small steps, about a quarter mark at a time.

The Blank Disc Test: Use It With Care

A popular trick is to lower the stylus onto a blank, grooveless record and watch the arm. If it drifts inward, add anti-skate. If it drifts outward, reduce it.

This test is not perfect. Friction on a smooth surface differs from friction in a real groove, so it can lead to settings that are too high. Use it as a rough check, then trust your ears with real music.

When You Can Leave It Alone

Some turntables do not need any adjustment. Many fully automatic decks set anti-skate and tracking force at the factory.

Linear tracking turntables move the arm straight across the record, so they have no skating force at all. If your deck has no dial, there is nothing to set.

  • Fully automatic entry decks, such as the Audio-Technica AT-LP60X family.
  • Linear tracking or tangential arm turntables.
  • Some DJ setups where users set anti-skate to zero for scratching.

A Note for DJs

Many scratch DJs set anti-skate to zero. When a record is moved back and forth by hand, the normal skating force does not apply in the same way, and zero can help the needle stay in the groove.

For normal listening and mixing, though, the match-the-force rule still gives the cleanest sound and the least wear.

Signs Your Anti-Skate Is Set Well

Once anti-skate is right, the changes are quiet but clear. Both channels sound equally clean, even on the loudest tracks near the end of a side.

Check the stylus from the front with a flashlight while the arm rests on a stopped record. The cantilever should point straight, not bent to the left or right.

  • Vocals sound clear in both speakers, with no extra harshness on one side.
  • The arm stays steady when you lower it onto the lead-in groove.
  • Loud passages near the label play without skips.
  • The stylus wears evenly, so it keeps sounding good for its full life.

Anti-Skate Settings and Their Effects

Listen near the end of a side to judge.

Setting What happens What you hear
Too low Stylus leans on inner wall Harsh right channel
Matched to tracking force Stylus centered Balanced, clean sound
Too high Stylus pushed outward Harsh left channel
Zero for scratching Needle stays in groove when moved Fine for DJ use only

Common Anti-Skate Mistakes

These mistakes are easy to make and easy to fix. Check for them if your sound is uneven.

  • Setting anti-skate before tracking force.
  • Leaving it at zero on a hi-fi deck after setup.
  • Turning it all the way up to stop skips, which moves the problem to the other channel.
  • Forgetting to reset it after changing cartridges.
  • Trusting the blank disc test alone.

Turntables With Adjustable Anti-Skate

Each of these models from our reviews has an anti-skate control you can set to match your cartridge.

Pro-Ject Debut PRO B

Pro-Ject Debut PRO B

Mentioned

Who Should Buy It

  • Pro-Ject fans who want a deck with a balanced design path and do not mind adding their own cartridge
  • Listeners who prioritize a stable plinth and aluminum platter over convenience features
  • Buyers who prefer manual speed control without automation
  • Users building a component system around a turntable with separate phono stage

Skip It If

  • You need an all-in-one turntable with built-in phono preamp and Bluetooth
  • You want a complete cartridge included and clearly listed in the product data
  • You require precise dimensions and weight before purchasing
Check Price on Amazon

We may earn a commission at no extra cost to you.

Last verified: October 2026

Technics SL-1210M5G

Technics SL-1210M5G

Mentioned

Who Should Buy It

  • Turntablists who need instant, stable torque for scratching and beat juggling
  • Vinyl collectors who DJ and want a trusted direct-drive mechanism
  • Club and bar installs that want a proven, familiar deck at the booth
  • DJs who value precise, repeatable one-button pitch switching

Skip It If

  • You have no mixer or phono preamp and do not plan to buy one
  • You only play digital files and never touch a physical record
  • You need confirmed weight and power figures before purchasing
Check Price on Amazon

We may earn a commission at no extra cost to you.

Last verified: November 2026

Audio-Technica AT-LP140XP-BK Direct-Drive DJ

Audio-Technica AT-LP140XP-BK Direct-Drive DJ

Mentioned

Who Should Buy It

  • Turntablists who want direct-drive precision with a balanced tonearm and quartz pitch control
  • Vinyl collectors who want a matched cartridge, headshell and cleaning kit in one bundle
  • Home listeners who want a turntable paired with ready-to-use powered bookshelf speakers
  • DJs assembling a two-turntable-and-mixer setup who need one professional direct-drive deck

Skip It If

  • You need a full DJ system with a built-in mixer
  • You already own bookshelf speakers or a record cleaning kit and do not need the bundle extras
  • You need confirmed turntable weight before buying
Check Price on Amazon

We may earn a commission at no extra cost to you.

Last verified: November 2026

Keep Reading

Related guides and picks on Mandrillis:

FAQs

That is the usual starting point and works well for most setups. Fine tune it by ear if one channel sounds harsher than the other.
On a hi-fi turntable it can cause uneven wear and distortion in one channel. Set it to match your tracking force unless you scratch records as a DJ.
Yes, too little can make the arm jump toward the center and too much can push it outward. Set tracking force first, then match the anti-skate.

About This Guide

M

Mandrillis Team

The Mandrillis editorial team researches and compares audio and music gear using manufacturer documentation, verified specs and real buyer feedback, so you can make a confident purchase without wading through marketing claims.

Read our full research methodology.