MANDRILLIS Better Gear. Better Sound.
How to Set Crossover Frequency on a Subwoofer (Easy Steps)

Guides

How to Set Crossover Frequency on a Subwoofer (Easy Steps)

The crossover decides which notes your subwoofer plays and which your main speakers handle. Set it wrong and bass can sound boomy, thin or oddly located. This guide explains what the crossover does, gives starting points by speaker size, and walks through setting it on a receiver or directly on the sub.

Quick Answer

Set the subwoofer crossover slightly above the lowest frequency your main speakers can play well. 80 Hz is the usual starting point. Small bookshelf or satellite speakers often need 100 to 120 Hz, while large floorstanding speakers may suit 60 Hz. If a receiver sets the crossover, turn the sub's own dial to its highest or LFE setting.

M Mandrillis Team • Expert guides. Real advice. • Last updated: Nov 22, 2026 • 5 min read

How this guide was put together

This guide is based on manufacturer manuals, published specifications and widely used audio reference standards. Mandrillis does not run hands-on tests for these guides, so treat figures as typical values and check the manual for your own gear before changing settings.

What a Subwoofer Crossover Does

A crossover is a filter that splits sound by pitch. Notes below the crossover point go to the subwoofer, and notes above it go to your main speakers.

The goal is a smooth handoff. You want the sub and speakers to sound like one system, with no gap or doubled bass where they meet.

  • Measured in hertz, written Hz.
  • Lower numbers mean deeper bass.
  • Common settings range from 60 to 120 Hz.
  • THX recommends 80 Hz as a standard starting point.

Why the Right Setting Matters

If the crossover is too low, small speakers try to play bass they cannot handle. Bass sounds thin and the speakers may distort at high volume.

If it is too high, the sub plays deeper voices and upper bass notes. You may start to hear exactly where the sub is in the room, which breaks the illusion.

Find Your Speakers' Low End First

Check the frequency response in your speakers' manual or spec sheet. Look for the lowest number, often listed as something like 50 Hz to 20 kHz.

Some makers list this at a tolerance such as plus or minus 3 dB. That number is the most useful one for setting a crossover.

A Simple Rule of Thumb

Set the crossover about 10 to 20 Hz above the lowest rated frequency of your speakers. That keeps them out of the range where they start to struggle.

  • Speakers rated down to 70 Hz: try 80 to 90 Hz.
  • Speakers rated down to 50 Hz: try 60 to 80 Hz.
  • Speakers rated down to 100 Hz: try 110 to 120 Hz.

Starting Crossover Points by Speaker Type

General starting points. Fine tune by ear in your own room.

Speaker type Typical woofer size Starting crossover
Small satellite speakers 3 to 4 inches 120 to 150 Hz
Small bookshelf speakers 4 to 5 inches 90 to 120 Hz
Medium bookshelf speakers 5 to 6.5 inches 80 Hz
Large bookshelf or small towers 6.5 to 8 inches 60 to 80 Hz
Large floorstanding speakers 8 inches or more 40 to 60 Hz

Setting the Crossover on an AV Receiver

If your subwoofer connects to a receiver's sub or LFE output, let the receiver handle the crossover. Receivers can set a different crossover for each speaker group.

Steps

Menus differ by brand, but most follow a similar path under speaker setup.

  • Run the receiver's auto setup with its microphone first, if it has one.
  • Open the speaker or bass management menu.
  • Set the main speakers to Small, which sends their deep bass to the sub.
  • Choose a crossover for each speaker group, starting at 80 Hz.
  • Set the subwoofer's own crossover dial to its highest setting, or to LFE if it has that position.

Why Turn the Sub Dial Up

If both the receiver and the sub apply a crossover, the two filters stack. This can create a dip in the bass near the crossover point.

Setting the sub dial to maximum or LFE bypasses or minimizes its own filter, so only the receiver's crossover is in use.

Setting the Crossover on the Subwoofer Itself

In a stereo system with no bass management, such as a stereo amp or powered speakers with a sub output, you set the crossover on the sub's dial.

Here the main speakers usually still play full range. The sub only fills in the deepest notes below the dial setting.

  • Start the dial near the lowest rated frequency of your speakers.
  • For full range bookshelf speakers, that often means 50 to 70 Hz.
  • Raise the dial slowly if there is a gap in the bass.
  • Lower it if bass sounds thick or doubled.

How to Fine Tune by Ear

Charts get you close, but every room is different. A few minutes of careful listening finishes the job.

A Simple Listening Routine

Sit in your main seat and use music with a bass line that walks up and down, plus a male vocal track.

  • Play the bass line and listen for notes that jump out or vanish.
  • Play the vocal track and make sure the voice does not seem to come from the sub.
  • Move the crossover by 10 Hz at a time and listen again.
  • Pick the setting where bass sounds even and the sub disappears into the speakers.

Do Not Forget Phase and Level

Crossover, phase and level work together. Change the crossover, then recheck the other two.

Flip the phase switch between 0 and 180 degrees while bass plays, and keep the setting that sounds fuller. Then set the level so bass blends in rather than stands out.

Common Crossover Mistakes

A few simple errors cause most crossover problems. Check these if bass still sounds wrong.

  • Setting speakers to Large on a receiver with small bookshelf speakers.
  • Leaving the sub dial low while the receiver also sets a crossover.
  • Setting the crossover above 120 Hz, which makes the sub easy to locate.
  • Changing the crossover without rechecking phase and level.
  • Judging bass from a seat other than your main listening spot.

A Note on Volume and Safety

Keep the volume moderate while tuning. Test tones and bass sweeps at high volume can be tiring and may harm your hearing.

Very low frequency tones played loud can also stress small speakers if the crossover is set too low. Raise the crossover if speakers buzz or crackle on deep notes.

The Bottom Line

Start the crossover at 80 Hz, or slightly above the lowest note your speakers play well. Use 100 to 120 Hz for small speakers and 60 Hz or lower for large towers.

With a receiver, set the speakers to Small and the sub dial to its highest or LFE setting. Then fine tune by ear and recheck phase and level.

Subwoofers and a Receiver From Our Reviews

Powered subwoofers with adjustable crossover dials and an AV receiver with bass management.

Klipsch R-120SW

Klipsch R-120SW

Mentioned

Who Should Buy It

  • Movie fans adding a subwoofer to a surround system
  • Music listeners who like electronic, hip hop, or action soundtracks
  • Owners of small to medium rooms who can place a rear ported sub
  • Buyers who want the Klipsch spun-copper woofer look

Skip It If

  • You need a subwoofer with known physical dimensions before buying
  • You want wireless streaming from a phone
  • You prefer a sealed cabinet for tighter transients
Check Price on Amazon

We may earn a commission at no extra cost to you.

Last verified: October 2026

Kanto SUB8VMB

Kanto SUB8VMB

Mentioned

Who Should Buy It

  • Desktop audio users with limited floor space
  • Kanto speaker owners wanting a matching matte black finish
  • Apartment dwellers seeking controlled low end without a large cabinet
  • Listeners who prefer an analog wired subwoofer with simple controls

Skip It If

  • You need maximum low frequency extension for home theater
  • You want wireless streaming or app control
  • You require full published specifications including RMS and input panel details
Check Price on Amazon

We may earn a commission at no extra cost to you.

Last verified: October 2026

Denon AVR-S670H

Denon AVR-S670H

Mentioned

Who Should Buy It

  • Buyers who want a specific, confirmed wattage figure rather than a vague power claim
  • Gamers who want VRR, ALLM, and QFT confirmed for reduced lag
  • Households who want HEOS multi-room streaming with Spotify and TIDAL
  • Anyone who wants full Alexa voice control for hands-free operation

Skip It If

  • You need a confirmed phono input
  • You need a named automatic room correction system
  • You need more than 5.1 channels for a larger speaker layout
Check Price on Amazon

We may earn a commission at no extra cost to you.

Last verified: November 2026

Keep Reading

Related guides and picks on Mandrillis:

FAQs

80 Hz is the most common starting point and works for many systems. Adjust up for small speakers or down for large towers.
Use the receiver when the sub connects to its LFE output. Then turn the sub's own dial to its highest or LFE setting.
The crossover is often set too high, so the sub plays notes your ears can locate. Lower it toward 80 Hz and reduce the sub level a little.

About This Guide

M

Mandrillis Team

The Mandrillis editorial team researches and compares audio and music gear using manufacturer documentation, verified specs and real buyer feedback, so you can make a confident purchase without wading through marketing claims.

Read our full research methodology.