Guides
How to Level a Turntable on an Uneven Surface (Step-by-Step)
A turntable that is not level makes the tonearm drift, wears one side of the stylus faster and can cause skips. This guide explains why level matters, the simple tools you need, and how to level a deck on an uneven shelf or floor with feet, shims or a platform.
Quick Answer
To level a turntable on an uneven surface, place a small bubble level on the center of the platter, then raise the low side by turning the adjustable feet or sliding thin shims under them. Check front to back and side to side, and confirm the deck does not rock. Recheck tracking force after leveling.
How this guide was put together
This guide is based on manufacturer manuals, published specifications and widely used audio reference standards. Mandrillis does not run hands-on tests for these guides, so treat figures as typical values and check the manual for your own gear before changing settings.
Why a Level Turntable Matters
The tonearm is balanced like a seesaw. When the platter tilts, gravity pulls the arm toward the low side. The stylus then leans on one wall of the groove more than the other.
That uneven pressure has real effects. You may hear one channel sound weaker, get skips on loud passages, or wear one side of the stylus and groove faster.
- A tilt toward the center makes the arm drift inward and can cause skips.
- A tilt toward the edge pulls the arm outward.
- A front to back tilt can change how the tonearm tracks and cues.
- Even a small tilt adds wear over hundreds of hours.
What You Need
Leveling takes about ten minutes and very few tools. You probably have most of them already.
- A small round bubble level, often sold as a turntable or camera level.
- Or a short line level placed in two directions, one after the other.
- Thin shims: cork, rubber pads, plastic shims or folded card for tiny gaps.
- A coin or a phone level app, if you have no bubble level.
- A helper to lift the turntable while you add shims, if it is heavy.
Step-by-Step: How to Level Your Turntable
Do this with the turntable unplugged and the tonearm locked on its rest. Take the record and mat off so the level sits flat on the platter.
Step 1: Level the Furniture First
Check the shelf or cabinet before the turntable. If the whole unit tilts, fix that first with furniture shims or by adjusting its feet.
Press each corner of the shelf. If it rocks, slide a shim under the short leg until it sits firm. A solid base makes the rest of the job much easier.
Step 2: Place the Level on the Platter
Put the bubble level on the center of the platter, next to the spindle. This is where leveling matters most, because it is where the record sits.
Note which way the bubble moves. The bubble always floats toward the high side.
Step 3: Adjust the Feet
Many turntables have feet that screw up and down. Turning a foot one way raises that corner. Turning it the other way lowers it.
Raise the low corners a little at a time, checking the bubble after each turn. Work in small steps, a quarter turn at a time.
Step 4: Add Shims If Your Feet Are Fixed
If your turntable has no adjustable feet, slide thin shims under the feet on the low side. Lift the deck gently by its base, never by the tonearm or platter.
Stack thin shims rather than using one thick one. That gives you finer control. Stop when the bubble sits centered.
Step 5: Check Both Directions
A round bubble level shows both directions at once. If you use a line level, check side to side first, then turn it ninety degrees and check front to back.
Rotate the platter by hand a quarter turn and check again. If the bubble moves as the platter turns, the platter itself may sit unevenly on its bearing.
Step 6: Confirm It Does Not Rock
Press gently on each corner of the turntable. All feet should stay firmly in contact, with no rocking.
A deck that is level but rocks on one foot can still pick up vibration. Adjust that foot down until it touches.
Options for Very Uneven Surfaces
Old floors and sloped shelves sometimes need more than shims. These fixes work when the gap is large.
Use a Leveling Platform
A thick board or isolation platform with its own adjustable feet sits between the shelf and the turntable. You level the platform once, then the turntable sits flat on top.
This also adds mass and isolation, which helps reduce vibration and feedback.
Move to a Wall Shelf
If the floor slopes or flexes, a wall shelf fixes both problems. Install it with a level from the start so it sits true.
Mount it into studs or anchors rated well above the turntable's weight, often between 8 and 25 pounds for common decks.
How to Tell If Leveling Fixed the Problem
Play a record you know well once the deck is level and the settings are reset. Listen for steadier sound and even volume from both speakers.
Watch the tonearm as the record plays. It should move smoothly toward the center with no sudden jumps. If skips continue, the cause is likely tracking force, a worn stylus or vibration rather than level.
- Both channels sound equally loud.
- Loud passages play without skipping.
- The tonearm stays put when you rest it above a stopped platter on the cue lever.
- The bubble stays centered after a full rotation of the platter.
After Leveling: Recheck Your Settings
Leveling can change how the tonearm balances. Take two more minutes to recheck the settings that depend on it.
Float the tonearm, zero the counterweight dial and set the tracking force again. Then match the anti-skate to the force.
- Rebalance the tonearm and reset tracking force.
- Set anti-skate to match the tracking force.
- Put the mat and a record back on, then play a track you know well.
- Recheck the level every few months, or after moving furniture.
Leveling Tools Compared
Pick what fits your surface.
| Tool | Best for | Notes |
|---|---|---|
| Adjustable feet | Small tilts | Turn a quarter turn at a time |
| Thin stacked shims | Decks with fixed feet | Lift by the base only |
| Leveling platform | Very uneven shelves | Also adds isolation |
| Wall shelf | Sloped or bouncy floors | Install level from the start |
Common Leveling Mistakes
These small errors undo good work. Avoid them and the deck stays level for a long time.
- Leveling the turntable base instead of the platter, where the record sits.
- Lifting the deck by the tonearm or platter to add shims.
- Using a single thick shim that tips the deck the other way.
- Forgetting to recheck tracking force afterward.
- Leveling on a shelf that still rocks underneath.
Turntables From Our Reviews
Some turntables include adjustable feet that make leveling easy. Check the specs of any model before you buy.
Technics SL-1210M5G
Mentioned
Who Should Buy It
- Turntablists who need instant, stable torque for scratching and beat juggling
- Vinyl collectors who DJ and want a trusted direct-drive mechanism
- Club and bar installs that want a proven, familiar deck at the booth
- DJs who value precise, repeatable one-button pitch switching
Skip It If
- You have no mixer or phono preamp and do not plan to buy one
- You only play digital files and never touch a physical record
- You need confirmed weight and power figures before purchasing
We may earn a commission at no extra cost to you.
Last verified: November 2026
Pro-Ject Debut PRO B
Mentioned
Who Should Buy It
- Pro-Ject fans who want a deck with a balanced design path and do not mind adding their own cartridge
- Listeners who prioritize a stable plinth and aluminum platter over convenience features
- Buyers who prefer manual speed control without automation
- Users building a component system around a turntable with separate phono stage
Skip It If
- You need an all-in-one turntable with built-in phono preamp and Bluetooth
- You want a complete cartridge included and clearly listed in the product data
- You require precise dimensions and weight before purchasing
We may earn a commission at no extra cost to you.
Last verified: October 2026
Audio-Technica AT-LP60XBT
Mentioned
Who Should Buy It
- Beginners who want a plug-and-play vinyl setup
- Desktop users needing compact powered monitors with balanced inputs
- Listeners who value automatic tonearm operation and Bluetooth streaming
- Those building a small room system with future upgrade potential
Skip It If
- You require a remote control for volume and track selection
- You have limited space without checking exact dimensions first
- You already own a receiver and passive speakers that would be underused
We may earn a commission at no extra cost to you.
Last verified: October 2026
Keep Reading
Related guides and picks on Mandrillis:
- How to Adjust Counterweight on a Turntable Without a Scale : reset tracking force after leveling
- Can You Put a Turntable on Top of a Speaker? : where to place your deck
- Best Turntables Under 500 : models with solid, adjustable feet
FAQs
About This Guide
Mandrillis Team
The Mandrillis editorial team researches and compares audio and music gear using manufacturer documentation, verified specs and real buyer feedback, so you can make a confident purchase without wading through marketing claims.
Read our full research methodology.